Author Topic: NEW 34 (Read 182264 times)

rescue5271 · « **Reply #200 on:** June 22, 2006, 12:55:03 PM »

those lines are ment to be in fireproff casing?

?

Firey9119 · « **Reply #201 on:** June 22, 2006, 06:33:18 PM »

has anyone noticed when the new 34s are started the radio ALWAYS comes on??
we have a number of time been trying to transmit a message(mobile most of the time) and had to stop the message to turn the radio off.

anyone had this trouble? short of pulling the fuse not sure if there is anything we can do with it.

Alan (Big Al) · « **Reply #202 on:** June 22, 2006, 07:50:40 PM »

We disconnected the speakers because of this and feedback we were getting....Down side is no radio on the long hauls

rescue5271 · « **Reply #203 on:** June 22, 2006, 08:46:31 PM »

report it and get it fixed;;;

medevac · « **Reply #204 on:** June 23, 2006, 03:22:26 AM »

hmm... problysomething to do withisolating the batteries i would geuss mate, would reset the system when you de-isolated it... but you probly knew that.

Mike · « **Reply #205 on:** June 23, 2006, 08:31:18 AM »

Never had the stereo turn itself on though... just lots of static noise over all the radios (still working on that one).

CFS_Firey · « **Reply #206 on:** June 23, 2006, 01:40:01 PM »

Isn't there a 'quality control' system in place that ensures all trucks are fully checked and tested before they are delivered to the brigades?
One would think that problems like radio static when you turn the truck on, would be fairly obvious to spot...

PF_ · « **Reply #207 on:** June 23, 2006, 01:55:04 PM »

Seems like there has been one big filtered up for new trucks

CFS_Firey · « **Reply #208 on:** June 23, 2006, 02:04:22 PM »

yeah, not wrong...

rescue5271 · « **Reply #209 on:** June 23, 2006, 03:58:50 PM »

No there is a OHSW inspection only not sure what moores do but cfa/skilled do a full run down,check pump,hoses,all that stuff before it leaves the workshop...With all the on going problems is it time to go to a real fire truck company?

?

PF_ · « **Reply #210 on:** June 23, 2006, 04:56:52 PM »

Does such a place exist in Australia?

Where are the MFS Scania's made?

rescue5271 · « **Reply #211 on:** June 23, 2006, 05:32:50 PM »

Yes in Ballarat Victoria called skilled engineering....

Scania_1 · « **Reply #212 on:** June 28, 2006, 07:54:45 PM »

MFS Scanias bodies from the latest batch were built by Liquip in Queensland, previous to that Fraser and Lowes (when they existed) in NZ

rescue5271 · « **Reply #213 on:** June 29, 2006, 06:53:32 AM »

i think we should just look on ebay or the internat and buy what we want nice large pumper from the state's.....

backburn · « **Reply #214 on:** July 02, 2006, 03:34:34 PM »

We had the BA cylander put in under the back seat the other day and we have found that when we get in we kick it and turn it on by mistake. Does this happen to any other new 34 around?

24P · « **Reply #215 on:** July 02, 2006, 03:38:30 PM »

Quote from: backburn on July 02, 2006, 03:34:34 PM

We had the BA cylander put in under the back seat the other day and we have found that when we get in we kick it and turn it on by mistake. Does this happen to any other new 34 around?

Why did you have a BA cylinder put under the seat?

rescue5271 · « **Reply #216 on:** July 02, 2006, 04:54:45 PM »

Ye,why did you put the cylinder under the seat???

medevac · « **Reply #217 on:** July 02, 2006, 05:16:22 PM »

is there another echo...

crank the post count up... so close to the 1000 mark.

medevac · « **Reply #218 on:** July 02, 2006, 06:12:46 PM »

just got this from a reasonably reliable source

"There is a BA cylinder bracket for a BA cylinder, for a system that was going to be installed in all the new 34’s, which enables BA masks to be hooked up inside the cab, and provide a short amount of breathing air for each crew member in a burn over situation… EG – 5 masks, all hooked in to the one cylinder… bout 6 mins each of air… Plenty for a burn over before you can get out."

Scania_1 · « **Reply #219 on:** July 02, 2006, 06:19:58 PM »

sounds good, but oxygen would be better than compressed air. You can change the rate (maybe) and oxygen does have a calming effect.

PF_ · « **Reply #220 on:** July 02, 2006, 06:35:18 PM »

What, no BA seats!?

medevac · « **Reply #221 on:** July 02, 2006, 06:43:10 PM »

Quote from: ath on July 02, 2006, 06:19:58 PM

sounds good, but oxygen would be better than compressed air. You can change the rate (maybe) and oxygen does have a calming effect.

just about flooding the cab with cool air i think, plus it might create a bit of positive pressure to keep moke out a lil bit

Toast · « **Reply #222 on:** July 02, 2006, 08:56:16 PM »

Quote from: P F on July 02, 2006, 06:35:18 PM

What, no BA seats!?

Ah but proper (EG: Not a crap bench seat like the DENNIS) BA seats will usually cut the max crew from 6 -> 5. Awesome seats though.

PF_ · « **Reply #223 on:** July 02, 2006, 09:10:38 PM »

Scania's have bench seats also, maybe thats the way BA Seats are, I got no idea. 5 Crew is really enough, dont needto have 6. BA seats in all appliances wouldnt be a bad idea, it is a lot easier and more productive to put the set on and get out with it on.

Toast · « **Reply #224 on:** July 03, 2006, 12:19:25 AM »

Not to mention the amount of space it will free up on the appliance.

Author Topic: NEW 34 (Read 182264 times)

rescue5271

rescue5271

PF_

rescue5271

PF_

rescue5271

rescue5271

rescue5271

PF_

Toast

PF_

Toast